Section 1 Steel Plates,Strips,Sections and Bars A.General Rules 1.Scope 1.1 General rules to be applied in the manufac- ture and testing of hot-rolled plates,strips,sections (including hollow sections),rods and bars are con-COR-TEN,CORTEN A,CORTEN STEEL,A242,A558 GRSpecifications for Corten Steel Strip Coil according tp Jis 3125-87(SPA-H SPA-C)JAPAN STANDARD Type Symbol C Si Mn P S Cu Cr Ni Yield N/mm2 TensileN/mm2 SPA-H 0.12 max 0.25 to 0.75 0.20 to 0.50 0.07 to 0.15 0.4 max 0.25 to0.60 0.30 to 1.25 0.65 max 343 min 481 min SPA-C 34 min 451 min Standards Europe Material no.D F GB USA J Salzgitter DIMENSIONS FOR HOT ROLLED STEEL BEAM,COLUMN,Under the steel economy programme,a rational,efficient and economical series of Indian Standards on beam sections,channel sections and angle sections was evolved in 1957 and IS 808 1957 was published covering junior,light weight,medium weight,wide flange and heavy
EN 10025-2 S235 steel is a non-alloy carbon structural steel grade,according to EN 10025-2,S235 material is devided into 3 quality grades S235JR (1.0038) Impact energy 27 Joules at room temperature 20 ,S235J0 (1.0114) Impact energy 27J at 0 ,and S235J2 (1.0117) Impact energy 27 J at -20 .EN10025 2-S235|S275|S355 Steel Plate SpecificationAGICO ANSON is able to supply all kinds of structural steel plate produced by En10025-2 standard,which mainly includes 4 major grades S235,S275,S355 and S450,there's also more specific steel grades for different mechanical properties.As same as common structural steel,steel plate and pipes under this standard are featured with good weldability,formability,hot forming,cold formability EVALUATION OF THE P S235JR STRUCTURAL CARBONthe main chemical and mechanical properties of the above-mentioned steel.COMPOSITION AND MAIN PROPERTIES OF S235JR STEEL Steel Designation S235JR is a European designation for steel that is better known in Lebanon as St 37-2 according to German standards (DIN),or as E 24-2 according to French standards NF (AFNOR).
Handbook of Comparative World Steel Standards Library of Congress Cataloging-in-Publication Data Handbook of comparative world steel standards / John E.Bringas,editor. 2 nd ed.p.cm (ASTM data series; DS 67A) ASTM stock number DS67A. ISBN 0-8031-3042-2 1.Steel Standards Handbooks,manuals,etc.,2.PRODUCTS HANDBOOK Structural SteelCONTINENTAL STEEL PTE LTD 100 Gul Circle,Singapore 629586.Phone (65) 68620033 Facs (65) 68616448/68624006.Website consteel.sg PRODUCTS HANDBOOK Structural SteelS235J0 steel plate - BEBON steelS235J0 steel plate,EN10025 S235J0 steel plate,under EN10025 standard,we can regard S235J0 steel plate as Carbon and low alloy steel S235J0 steel plate is one mainly of Carbon and low alloy steel,S235J0 steel plate would be used to built containers which can bear low temperature sea water.Chemical composition % of grade S235J0 steel
Properties of steel S235JR (1.0038(dubl)) Weldability This steel grade is generally suitable to welding Equivalent grades of steel S235JR (1.0038(dubl))STAINLESS STEEL GRADES PERFORMANCESstainless steel AISI 201 which is the most appropriate grade for industrial doors.AISI 304 Well known stainless steel grade,very close to the 201 grade but with lower mechanical properties.AISI 316 Well known stainless steel as well,with very high corrosion resistance,it isSTRUCTURAL STEEL SECTION FACTOR General Guidelinesof the steel exposed to the fire and the mass of the steel section.The higher the Hp/A,the faster the steel section heats up and so the greater the thickness of fire protection material required.It should be noted that in European design standards,the section factor is presented as A/V which has the same numerical value as Hp/A.
Type 321 G 4304 SUS321 (3) 1501-321S12 17440/1 X6CrNiTi1810 1449-321S31 Type 347 G 4304 SUS347 (3) 1501-347S17 17440/1 X6CrNiNb1810 1449-347S31 Note (1) Specify mechanical properties,test and inspection in accordance with ASTM.Some results are removed in response to a notice of local law requirement.For more information,please see here.12345NextSteel material properties - SteelConstructionfoStrength  Yield strengtYield strength is the most common property that the designer will need as it is the basis used for most of the rules given in design codes.In European Standards for structural carbon steels (including weathering steel),the primary designation relates to the yield strength,e.g.S355 steel is a structural steel with a specified minimum yield strength of 355 N/mm².
H-Beams.Rolled steel with an H-shaped cross-section.Equal thickness in the two parallel flanges with no taper on the inside surface.Classified into narrow,medium,and wide,based on